March 31, 2025, 03:13:14 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Dr1ft1ng0wns

Pages: [1] 2 3 ... 80
1
Electronics / Re: Headlights, tails, more
« on: March 14, 2015, 09:54:26 PM »
None of the lights run through the ecu. All the lights are in the harness on the driver side of the engine bay. My car has all of the ecu wiring removed along with the ecu itself and all the lights work. All you should have to do to get the lights working is put power into the fusebox on the driver side strut tower.

2
Cars for sale / Re: WTB: subaru, mazda, honda, nissan, shell
« on: February 25, 2015, 11:08:27 AM »
i paid 300 for my FC roller 6-7 years ago with a clean title. They're out there.

3
Drivetrain / Re: NV3500?
« on: October 14, 2014, 11:07:47 PM »


The shifter for an s10 tranny looks like its a solid 12" further fowards than the lt1 t56 it is pictured next to. I have the lt1 t56 in my car and it required moving the shifter back an 1" to center it in the hole. How are you planning on moving the shifter back 13"?

4
Drivetrain / Re: NV3500?
« on: October 14, 2014, 09:08:29 AM »
Probably not. You could maybe make it work if you removed the dash and cut a shifter hole where your stereo used to be. Plus the gear spread is terrible for a car. and then it would shift like...well.... the truck it came out of.   

5
Electronics / Re: Temp Gauge reading low; Overheating LS1
« on: October 09, 2014, 10:21:43 PM »
It's not built in but it's super easy to wire up. I think there are only 4 wires iirc.

6
Electronics / Re: Starting problems...Pez chassy harness
« on: October 06, 2014, 09:53:06 PM »
4g here as well.

7
Electronics / Re: Starting problems...Pez chassy harness
« on: October 06, 2014, 09:20:02 PM »
Battery good? What size cable running to the starter? Getting full voltage to starter solenoid? Motor should crank at least regardless of the engine harness.

8
Drivetrain / Re: L36 / T5 / GM 7.5" into '83 for 50 MPG
« on: October 05, 2014, 02:43:19 PM »
But if he"s building it for mileage i highly doubt the skinny pedal will get used a whole lot. And i would think smaller rear end = less rotating mass and less parasitic loss? (maybe a negligible amount, but still) Definitely going to have to watch this one. I would love a car that got 40-50 mpg and still had enough power to get around the slow people on the daily commute.

9
The Lounge / Re: What do you do for a living?
« on: September 03, 2014, 04:13:16 PM »
Haha crazy how things change. I now inspect semi truck retreads and am going into my third year of college, going for a bachelors in mechanical engineering.

10
The Lounge / Re: Explanation of the hot/crazy line
« on: September 03, 2014, 04:09:04 PM »
I don't know which is more awesome, the video itself or all of the pissed off crazy chicks in the comments haha.

11
Parts for Sale / Re: FS - Cobra 8.8 pinion flange
« on: August 07, 2014, 08:33:31 AM »
is that the smaller one required for the ronin fc 8.8?

12
Cars for sale / Re: RX7 FC - LS1 - Widebody - Big Wheels
« on: August 06, 2014, 03:59:04 PM »
Well it looks sweet man. Hopefully i get a chance to see it before it leaves!

13
Cars for sale / Re: RX7 FC - LS1 - Widebody - Big Wheels
« on: August 05, 2014, 04:04:45 PM »
This car is in bend?!?! Why have i never seen it before? Looks awesome! I'm over in prineville, like 45 minutes away.

14
Events / Re: Mini PNW Meet? Formula D
« on: June 21, 2014, 07:37:23 PM »
I'm pretty sure i"ll be there! might not be with the fc but i'll be there!

15
Parts for Sale / Re: Forgeline SP3 Rims 18x8 18x11 New
« on: June 11, 2014, 09:07:32 AM »
Quote from: Mik3ymomo on June 11, 2014, 06:40:01 AM
170mphparachute is that you?


Exactly what i was thinking lol.

Pages: [1] 2 3 ... 80