1
Electronics / Re: Harness Wrapping?
« on: May 08, 2014, 03:48:29 PM »
yes my car is being fixed lol.
March 18, 2025, 07:22:47 AM
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Electronics / Harness Wrapping?
« on: May 06, 2014, 09:11:49 PM »
Ok guys im at a cross roads here. I bought a bunch of techflex F6 split braid for my engine harness while this stuff is very nice for straight runs of cable it opens up on any bend. What have you guys used to wrap your harnesses. I even tried wrapping a section of it in self fusing tape but i do not like how it looks.
3
General Tech / Re: Surface Prep For Dynamat
« on: April 21, 2014, 08:40:22 PM »
I decided to do a layer of second skin audio damplifier pro then a layer of closed cell foam on the floor board all the way to the trunk. I will be covering the trans tunnel with luxury liner from SS to control heat. I dont want to go through the mission of spraying the whole interior. I sprayed the whole floor with VHT epoxy paint and putting the SS damplifier over that.
4
Electronics / Re: Tres' Custom Engine/Chassis Harness
« on: April 21, 2014, 08:20:22 PM »
I did this to.my fd but i kept abs but basically did.the same only lights fan power and parking lights go to to the front abs wipers and all that go along the fire wall and back out the other side. It was a pain in the arse.
5
General Tech / Re: HalfSpec's 2014 FD AC Group Buy
« on: April 12, 2014, 07:08:09 PM »
Also would like a set im using hinson radiator.
6
General Tech / Re: Surface Prep For Dynamat
« on: March 02, 2014, 08:25:24 AM »
Thanks for the info. Gonna replace the oem stuff pretty much exactly as it was. Then gonna run a layer of closed cell foam over everything.
7
General Tech / Re: Pcm harness fire wall hole.
« on: March 02, 2014, 08:20:53 AM »
Hmmm what car did you find one from i really wanted to put on something new but like it was mentioned above i have had no luck finding caps that big. I was thinking of shaping one out of bondo and sealing it with rtv for the holes where the front harness came in through but as far as the pcm i have been stumped.
8
General Tech / Pcm harness fire wall hole.
« on: March 01, 2014, 08:45:45 PM »
I would like to know what you guys are using to seal the hole where the ls1 harness comes through. I want to try and get it plugged up now while I have the dash and all the AC components out.there are also two holes were the original front harness came into the chassis on the driver side that I no longer use it's about two and a half inches and other one is about inch and a half anyone know where I can find some plugs to plug Thoes up.
9
General Tech / Re: Surface Prep For Dynamat
« on: March 01, 2014, 08:41:03 PM »
So this would be a superior product to dynamat extreme?
http://store.secondskinaudio.com/damplifier-pro-36-50-sq-feet-bulk-pack/
It looks like it is. I want to avoid the spray on kind and im not going for 100% coverage. Just replacing the oem stuff in the areas it was originally, then the spare tire area and the area from the bins back.
http://store.secondskinaudio.com/damplifier-pro-36-50-sq-feet-bulk-pack/
It looks like it is. I want to avoid the spray on kind and im not going for 100% coverage. Just replacing the oem stuff in the areas it was originally, then the spare tire area and the area from the bins back.
10
General Tech / Re: Surface Prep For Dynamat
« on: February 26, 2014, 07:06:56 PM »
And installation of lizard skin is not an option i have no air compressor.
11
General Tech / Re: Surface Prep For Dynamat
« on: February 26, 2014, 06:56:50 PM »
Weight is not a concern comfort and road noise is. Im tired of my leg and trans tunnel feeling like they are on fire. I want maximum sound deadening and tempature control. Im even droping the trans to design some heatsheilds with that expensive heat reflecting crap all through out the trans tunnel. Also looking at getting my stainless downpipes ceramic coated to further reduce in car temps. If not dynamat does lizard skin provide the same effect?
12
General Tech / Re: Surface Prep For Dynamat
« on: February 12, 2014, 04:48:37 PM »
And im sorry did mean i bought meant going to buy so if any one can reccomend something better lmk. I was thinking getting a gallon of second skin layit on thin then throw the dynamat on it.
13
General Tech / Surface Prep For Dynamat
« on: February 12, 2014, 04:41:22 PM »
I bought a mega pack of dynamat xtreme to line my now oem sound deadening free floor boards and trunk. Now in the process of removing the SD there a bunch of nicks and scrapes where bare metal is exposed. Should i prime the whole floor board where the dynamat will go or just put the dynamat over it and be done with. I dont feel comfortable putting the dynamat over bare metal but if it will be ok because the adhesive on the dynamat i wont worry about it. Also in removing the stinger road kill the PO installed in the trunk he did not properly install the stuff and left pockets in the spare tire well now i have 2 fairly large rust holes fml....
14
General Tech / Re: FD cooling system?
« on: January 29, 2014, 08:17:06 PM »
Hinson rad and taurus fan here in miami fans come on at 210 puts it to 195 in no time in stop in go traffic 90* weather.
15
Electronics / Re: relay with a resistor? please help
« on: January 29, 2014, 05:48:35 PM »
Well the emergency setup worked well for about 2 gears lol. The problem was ghat i would have to wiggle the key a bit for it to start so i dissasembled the ignition switch and it had worn down a bit where i believe the starter gets power from i bent it back up a bit and 1.5 years later no issues. I do believe the fd ignition switch can handle it but either way im going push button start so the ign switch can take it easy lol.