1
Cars for sale / Re: Parts or whole 87 RX7 luxury, 2 351,t5 and more Indiana
« on: December 17, 2015, 06:29:53 PM »
Ill try to post but most are in the build thread
March 16, 2025, 02:30:11 AM
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Cars for sale / Parts or whole 87 RX7 luxury, 2 351,t5 and more Indiana
« on: December 12, 2015, 11:23:48 AM »
http://www.norotors.com/index.php?topic=22825.45
Build thread
I'm selling or parting out my 87 rx7 project
I'm having my 2nd kid so I'm switching to a STI.
87 RX7 Luxury
Clean title
Very little rust
No engine but has a manual trans
$600
80s 351 engine
600cfm Holley carb
Elderbrock intake
New Manual fuel pump
Bbk 351 swap headers
Gear driven timing
5.0 valve covers
New gaskets
New belt pulleys
Setting up for manual rack but still have all the other accessories.
$950
95 351 out of a bronco
Ran when pulled
Efi but was converting to carb when I built it.
Should be a roller but can't confirm
$350
T5 wc t5
Worked good.
$500
T5 bell $100
Stage II clutch $200
I have misc stuff to throw in
Sure I have more
$2500 for all of it.
Text Josh 260-610-2610
Build thread
I'm selling or parting out my 87 rx7 project
I'm having my 2nd kid so I'm switching to a STI.
87 RX7 Luxury
Clean title
Very little rust
No engine but has a manual trans
$600
80s 351 engine
600cfm Holley carb
Elderbrock intake
New Manual fuel pump
Bbk 351 swap headers
Gear driven timing
5.0 valve covers
New gaskets
New belt pulleys
Setting up for manual rack but still have all the other accessories.
$950
95 351 out of a bronco
Ran when pulled
Efi but was converting to carb when I built it.
Should be a roller but can't confirm
$350
T5 wc t5
Worked good.
$500
T5 bell $100
Stage II clutch $200
I have misc stuff to throw in
Sure I have more
$2500 for all of it.
Text Josh 260-610-2610
3
Build Threads / Re: 351 into a 87 Rx7 luxury Build thread ...now for sale
« on: December 07, 2015, 08:47:27 PM »
Car is for sale.
Expecting my 2nd kid and am looking at sti's.
$3k obo for all of it.
Will make a legit for sale thread later.
Expecting my 2nd kid and am looking at sti's.
$3k obo for all of it.
Will make a legit for sale thread later.
4
Build Threads / Re: 351 into a 87 Rx7 luxury Build thread
« on: October 07, 2015, 04:21:42 PM »
No problem on the thread jack. I like the Info as well
5
Build Threads / Re: 351 into a 87 Rx7 luxury Build thread
« on: October 03, 2015, 10:10:35 AM »
Thanks guys it's getting there.
Will do orracle
Will do orracle
6
Build Threads / Re: 351 into a 87 Rx7 luxury Build thread
« on: September 30, 2015, 08:25:31 PM »
I'm going with a fuel cell not using the stock tank.
It keeps it simple is the main reason why.
No issue with cranking it for a min imo. Honesty I've never known it to take that long after a car has been sitting.
Progress is stalled at the moment. It's getting cold out so fire wood and getting the shop cleaned up is priority
It keeps it simple is the main reason why.
No issue with cranking it for a min imo. Honesty I've never known it to take that long after a car has been sitting.
Progress is stalled at the moment. It's getting cold out so fire wood and getting the shop cleaned up is priority
7
Build Threads / Re: 351 into a 87 Rx7 luxury Build thread
« on: September 17, 2015, 10:34:12 PM »
Reverse rotation water pump = we have issues with using a 6 rib pulley.
Fix
T5 getting together
Mechanical fuel pump
Also installed the headers valve covers etc.
Also the guy before me painted it red...now it's faded to chevy orange
Fix
T5 getting together
Mechanical fuel pump
Also installed the headers valve covers etc.
Also the guy before me painted it red...now it's faded to chevy orange
9
Parts for Sale / Re: Granny V8 engine cradle and trans Swap kit
« on: September 12, 2015, 09:46:35 PM »What platform?
I tested the guy
Sbf with unknown trans cross member and a bag of hardware
10
Build Threads / Re: My 88 TII SBF 351w Swap Adventure
« on: September 11, 2015, 09:51:52 PM »
Curious what you did to mount the slave to your t5?
My understanding is all t5 were cable so you make a small bracket and bolt on the slave. Did granny kit come with this?
I can get a slave cheaper then granny but if it's all there why not.
My understanding is all t5 were cable so you make a small bracket and bolt on the slave. Did granny kit come with this?
I can get a slave cheaper then granny but if it's all there why not.
11
Parts for Sale / Re: Pa, Fc ford 5.0 swap kit 302 Engine, t5 trans, grannys kit 1500
« on: September 09, 2015, 04:54:02 PM »
I'm interested in the granny kit.
12
Parts WTB / Wtb sbf swap kit
« on: September 06, 2015, 09:18:54 AM »
Looking for a used or new 351 swap kit before buying new
13
Build Threads / Re: 351 into a 87 Rx7 luxury Build thread
« on: September 05, 2015, 05:37:23 PM »
14
Build Threads / Re: 351 into a 87 Rx7 luxury Build thread
« on: September 05, 2015, 05:26:01 PM »
I bought the 84 carbed 351. It's a lot nicer then mine lol
Not sure if its truly a 84 but ill try to find out.
Came with
Rear sump oil pan
Holley 600cfm cam
Elderbrock intake
Dizzy and other electrical stuff.
Alternator is also already mounted low.
I just need to figure out how to run my water pump and I'm just going to use this engine and build my roller.
Pics to come
Not sure if its truly a 84 but ill try to find out.
Came with
Rear sump oil pan
Holley 600cfm cam
Elderbrock intake
Dizzy and other electrical stuff.
Alternator is also already mounted low.
I just need to figure out how to run my water pump and I'm just going to use this engine and build my roller.
Pics to come
15
Build Threads / Re: 351 into a 87 Rx7 luxury Build thread
« on: September 03, 2015, 02:27:19 PM »
I'm going to go look at a 84 351 which has Holley carb, elderock intake ect ect. Plan was to use the carb components on my 95 roller engine.
Or do I put no money into this engine and beat the piss out of it and build my roller on the side?
I'm afraid it will be a slow crappy sounding pos and I'll just rip it back out lol
Or do I put no money into this engine and beat the piss out of it and build my roller on the side?
I'm afraid it will be a slow crappy sounding pos and I'll just rip it back out lol